Пересобрал 2/4/25 с agpgart внутри. Вот куски из логов.
Код: Выделить всё
(II) fglrx(0): initializing int10
(II) fglrx(0): Primary V_BIOS segment is: 0xc000
(**) fglrx(0): Option "mtrr" "on"
(--) fglrx(0): Chipset: "ATI RV250SE Yd (R9200SE)" (Chipset = 0x5964)
(--) fglrx(0): (PciSubVendor = 0x1458, PciSubDevice = 0x4018)
(--) fglrx(0): board vendor info: third party grafics adapter - NOT original ATI
(--) fglrx(0): Linear framebuffer (phys) at 0xd8000000
(--) fglrx(0): MMIO registers at 0xe0020000
(--) fglrx(0): ChipExtRevID = 0x01
(--) fglrx(0): ChipIntRevID = 0x00
(--) fglrx(0): VideoRAM: 65536 kByte (64-bit DDR SDRAM)
(WW) fglrx(0): board is an unknown third party board, chipset is supported
(II) Loading sub module "ddc"
(II) LoadModule: "ddc"
(II) Loading /usr/X11R6/lib/modules/libddc.a
(II) Module ddc: vendor="The XFree86 Project"
compiled for 4.3.0.1, module version = 1.0.0
ABI class: XFree86 Video Driver, version 0.6
(II) Loading sub module "i2c"
(II) LoadModule: "i2c"
(II) Loading /usr/X11R6/lib/modules/libi2c.a
(II) Module i2c: vendor="The XFree86 Project"
compiled for 4.3.0.1, module version = 1.2.0
ABI class: XFree86 Video Driver, version 0.6
(II) fglrx(0): I2C bus "DDC" initialized.
(II) fglrx(0): Connector Layout from BIOS --------
(II) fglrx(0): Connector1: DDCType-3, DACType-0, TMDSType--1, ConnectorType-2
(**) fglrx(0): MonitorLayout Option:
Monitor1--Type AUTO, Monitor2--Type AUTO
(II) fglrx(0): DDC detected on DDCType 3 with Monitor Type 0
(II) fglrx(0): Primary head:
Monitor -- NONE
Connector -- None
DAC Type -- Unknown
TMDS Type -- NONE
DDC Type -- NONE
(II) fglrx(0): Secondary head:
Monitor -- CRT
Connector -- VGA
DAC Type -- Primary
TMDS Type -- NONE
DDC Type -- VGA_DDC
(II) fglrx(0):
(II) fglrx(0): DesktopSetup 0x0000
(**) fglrx(0): PseudoColor visuals disabled
(**) fglrx(0): Overlay disabled
(**) fglrx(0): Overlay disabled
(II) fglrx(0): PLL parameters: rf=2700 rd=12 min=20000 max=40000; xclk=20000
(==) fglrx(0): Using gamma correction (1.0, 1.0, 1.0)
(**) fglrx(0): Center Mode is disabled
(==) fglrx(0): TMDS coherent mode is enabled
(II) fglrx(0): Monitor0: Using hsync range of 31.00-86.00 kHz
(II) fglrx(0): Monitor0: Using vrefresh range of 85.00-120.00 Hz
(II) fglrx(0): Clock range: 20.00 to 400.00 MHz
(II) fglrx(0): Not using mode "1280x1024" (no mode of this name)
(--) fglrx(0): Virtual size is 1280x960 (pitch 1280)
(**) fglrx(0): Default mode "1280x960": 148.5 MHz, 85.9 kHz, 85.0 Hz
(II) fglrx(0): Modeline "1280x960" 148.50 1280 1344 1504 1728 960 961 964 1011 +hsync +vsync
(**) fglrx(0): Default mode "1024x768": 94.5 MHz, 68.7 kHz, 85.0 Hz
(II) fglrx(0): Modeline "1024x768" 94.50 1024 1072 1168 1376 768 769 772 808 +hsync +vsync
(**) fglrx(0): Default mode "1024x768": 44.9 MHz, 35.5 kHz, 87.1 Hz (I)
(II) fglrx(0): Modeline "1024x768" 44.90 1024 1032 1208 1264 768 768 776 817 interlace +hsync +vsync
(**) fglrx(0): Default mode "800x600": 56.3 MHz, 53.7 kHz, 85.1 Hz
(II) fglrx(0): Modeline "800x600" 56.30 800 832 896 1048 600 601 604 631 +hsync +vsync
(**) fglrx(0): Default mode "640x480": 74.2 MHz, 85.9 kHz, 85.1 Hz (D)
(II) fglrx(0): Modeline "640x480" 74.25 640 672 752 864 480 480 482 505 doublescan +hsync +vsync
(**) fglrx(0): Default mode "640x480": 36.0 MHz, 43.3 kHz, 85.0 Hz
(II) fglrx(0): Modeline "640x480" 36.00 640 696 752 832 480 481 484 509 -hsync -vsync
(**) fglrx(0): Default mode "720x400": 35.5 MHz, 37.9 kHz, 85.0 Hz
(II) fglrx(0): Modeline "720x400" 35.50 720 756 828 936 400 401 404 446 -hsync +vsync
(**) fglrx(0): Default mode "640x400": 31.5 MHz, 37.9 kHz, 85.1 Hz
(II) fglrx(0): Modeline "640x400" 31.50 640 672 736 832 400 401 404 445 -hsync +vsync
(**) fglrx(0): Default mode "640x350": 31.5 MHz, 37.9 kHz, 85.1 Hz
(II) fglrx(0): Modeline "640x350" 31.50 640 672 736 832 350 382 385 445 +hsync -vsync
(**) fglrx(0): Default mode "512x384": 47.2 MHz, 68.7 kHz, 85.0 Hz (D)
(II) fglrx(0): Modeline "512x384" 47.25 512 536 584 688 384 384 386 404 doublescan +hsync +vsync
(**) fglrx(0): Default mode "512x384": 22.4 MHz, 35.5 kHz, 87.1 Hz (D)
(II) fglrx(0): Modeline "512x384" 22.45 512 516 604 632 384 384 388 409 interlace doublescan +hsync +vsync
(**) fglrx(0): Default mode "400x300": 28.1 MHz, 53.7 kHz, 85.3 Hz (D)
(II) fglrx(0): Modeline "400x300" 28.15 400 416 448 524 300 300 302 315 doublescan +hsync +vsync
(==) fglrx(0): DPI set to (75, 75)
(II) Loading sub module "fb"
(II) LoadModule: "fb"
(II) Loading /usr/X11R6/lib/modules/libfb.a
(II) Module fb: vendor="The XFree86 Project"
compiled for 4.3.0.1, module version = 1.0.0
ABI class: XFree86 ANSI C Emulation, version 0.2
(II) Loading sub module "ramdac"
(II) LoadModule: "ramdac"
(II) Loading /usr/X11R6/lib/modules/libramdac.a
(II) Module ramdac: vendor="The XFree86 Project"
compiled for 4.3.0.1, module version = 0.1.0
ABI class: XFree86 Video Driver, version 0.6
(**) fglrx(0): NoAccel = NO
(II) Loading sub module "xaa"
(II) LoadModule: "xaa"
(II) Loading /usr/X11R6/lib/modules/libxaa.a
(II) Module xaa: vendor="The XFree86 Project"
compiled for 4.3.0.1, module version = 1.1.0
ABI class: XFree86 Video Driver, version 0.6
(==) fglrx(0): HPV inactive
(==) fglrx(0): FSAA enabled: NO
(**) fglrx(0): FSAA Gamma enabled
(**) fglrx(0): FSAA Multisample Position is fix
(**) fglrx(0): NoDRI = NO
(II) Loading sub module "fglrxdrm"
(II) LoadModule: "fglrxdrm"
(II) Loading /usr/X11R6/lib/modules/linux/libfglrxdrm.a
(II) Module fglrxdrm: vendor="Fire GL - ATI Research GmbH, Germany"
compiled for 4.3.0.1, module version = 3.7.6
ABI class: XFree86 Server Extension, version 0.2
(II) fglrx(0): Depth moves disabled by default
(**) fglrx(0): Capabilities: 0x00000000
(**) fglrx(0): cpuFlags: 0x4000000f
(**) fglrx(0): cpuSpeedMHz: 0x00000730
(==) fglrx(0): OpenGL ClientDriverName: "fglrx_dri.so"
(**) fglrx(0): using built in AGPGART module: no
(**) fglrx(0): UseFastTLS=0
(**) fglrx(0): BlockSignalsOnLock=1
(==) fglrx(0): EnablePrivateBackZ = NO
(II) fglrx(0): using CAIL version [ATI LIB=CAIL.LIB,IA32,2.0024]
(--) Depth 24 pixmap format is 32 bpp
(II) do I need RAC? No, I don't.
(II) resource ranges after preInit:
[0] 0 0 0xe0020000 - 0xe002ffff (0x10000) MX[B]
[1] 0 0 0xd8000000 - 0xdbffffff (0x4000000) MX[B]
[2] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[3] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[4] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[5] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[6] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[7] -1 0 0xe1001000 - 0xe1001fff (0x1000) MX[B]
[8] -1 0 0xe2085000 - 0xe208503f (0x40) MX[B]
[9] -1 0 0xe2084000 - 0xe20847ff (0x800) MX[B]
[10] -1 0 0xe2081000 - 0xe2081fff (0x1000) MX[B]
[11] -1 0 0xe2000000 - 0xe207ffff (0x80000) MX[B]
[12] -1 0 0xe2087000 - 0xe2087fff (0x1000) MX[B]
[13] -1 0 0xe2086000 - 0xe20860ff (0x100) MX[B]
[14] -1 0 0xe2083000 - 0xe2083fff (0x1000) MX[B]
[15] -1 0 0xe2080000 - 0xe2080fff (0x1000) MX[B]
[16] -1 0 0xd0000000 - 0xcfffffff (0x0) MX[B]O
[17] -1 0 0xe0020000 - 0xe002ffff (0x10000) MX[B](B)
[18] -1 0 0xd8000000 - 0xdbffffff (0x4000000) MX[B](B)
[19] -1 0 0xe1000000 - 0xe1000fff (0x1000) MX[B](B)
[20] -1 0 0xe0030000 - 0xe003ffff (0x10000) MX[B](B)
[21] -1 0 0xdc000000 - 0xdfffffff (0x4000000) MX[B](B)
[22] 0 0 0x000a0000 - 0x000affff (0x10000) MS[B]
[23] 0 0 0x000b0000 - 0x000b7fff (0x8000) MS[B]
[24] 0 0 0x000b8000 - 0x000bffff (0x8000) MS[B]
[25] 0 0 0x0000c000 - 0x0000c0ff (0x100) IX[B]
[26] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[27] -1 0 0x00000000 - 0x000000ff (0x100) IX[B]
[28] -1 0 0x0000f000 - 0x0000f00f (0x10) IX[B]
[29] -1 0 0x0000d800 - 0x0000d87f (0x80) IX[B]
[30] -1 0 0x0000d400 - 0x0000d4ff (0x100) IX[B]
[31] -1 0 0x0000d000 - 0x0000d007 (0x8) IX[B]
[32] -1 0 0x0000e400 - 0x0000e41f (0x20) IX[B]
[33] -1 0 0x0000c000 - 0x0000c0ff (0x100) IX[B](B)
[34] 0 0 0x000003b0 - 0x000003bb (0xc) IS[B]
[35] 0 0 0x000003c0 - 0x000003df (0x20) IS[B]
(WW) fglrx(0): Cannot read colourmap from VGA. Will restore with default
(II) fglrx(0): UMM area: 0xd86b0000 (size=0x03950000)
(II) fglrx(0): driver needs XFree86 version: 4.3.x
(II) fglrx(0): detected XFree86 version: 4.3.0
(II) Loading extension ATIFGLRXDRI
(II) fglrx(0): doing DRIScreenInit
drmOpenDevice: minor is 0
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 7, (OK)
drmOpenDevice: minor is 0
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 7, (OK)
drmOpenDevice: minor is 0
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 7, (OK)
drmGetBusid returned ''
(II) fglrx(0): [drm] created "fglrx" driver at busid "PCI:2:0:0"
(II) fglrx(0): [drm] added 8192 byte SAREA at 0xe0cd9000
(II) fglrx(0): [drm] mapped SAREA 0xe0cd9000 to 0x40018000
(II) fglrx(0): [drm] framebuffer handle = 0xd8000000
(II) fglrx(0): [drm] added 1 reserved context for kernel
(II) fglrx(0): DRIScreenInit done
(II) fglrx(0): Kernel Module Version Information:
(II) fglrx(0): Name: fglrx
(II) fglrx(0): Version: 3.7.6
(II) fglrx(0): Date: Mar 5 2004
(II) fglrx(0): Desc: ATI Fire GL DRM kernel module
(II) fglrx(0): Kernel Module version matches driver.
(II) fglrx(0): Kernel Module Build Time Information:
(II) fglrx(0): Build-Kernel UTS_RELEASE: 2.4.25-lck-radeon3
(II) fglrx(0): Build-Kernel MODVERSIONS: yes
(II) fglrx(0): Build-Kernel __SMP__: no
(II) fglrx(0): Build-Kernel PAGE_SIZE: 0x1000
(II) fglrx(0): [drm] register handle = 0xe0020000
(II) fglrx(0): [agp] Mode=0x1f00421b bridge: 0x10de/0x01e0
(II) fglrx(0): [agp] AGP v1/2 disable mask 0x00000000
(II) fglrx(0): [agp] AGP v3 disable mask 0x00000000
(II) fglrx(0): [agp] enabling AGP with mode=0x1f00431a
(II) fglrx(0): [agp] AGP protocoll is enabled for grafics board. (cmd=0x1f004312)
(II) fglrx(0): [agp] grafics chipset has AGP v3.0 (native mode)
(II) fglrx(0): [drm] ringbuffer size = 0x00100000 bytes
(II) fglrx(0): [drm] DRM buffer queue setup: nbufs = 100 bufsize = 28672
(II) fglrx(0): [drm] texture shared area handle = 0xe4df3000
(II) fglrx(0): shared FSAAScale=1
(II) fglrx(0): DRI initialization successfull!
(II) fglrx(0): FBADPhys: 0xd8000000 FBMappedSize: 0x006b0000
(II) fglrx(0): Splitting WC range: base: 0xd8000000, size: 0x6b0000
(II) fglrx(0): Splitting WC range: base: 0xd8400000, size: 0x2b0000
(II) fglrx(0): Splitting WC range: base: 0xd8600000, size: 0xb0000
(II) fglrx(0): Splitting WC range: base: 0xd8680000, size: 0x30000
(**) fglrx(0): Write-combining range (0xd86a0000,0x10000)
(**) fglrx(0): Write-combining range (0xd8680000,0x30000)
(**) fglrx(0): Write-combining range (0xd8600000,0xb0000)
(**) fglrx(0): Write-combining range (0xd8400000,0x2b0000)
(**) fglrx(0): Write-combining range (0xd8000000,0x6b0000)
(II) fglrx(0): FBMM initialized for area (0,0)-(1280,1369)
(II) fglrx(0): FBMM auto alloc for area (0,0)-(1280,960) (front color buffer - assumption)
(==) fglrx(0): Backing store disabled
(==) fglrx(0): Silken mouse enabled
(II) fglrx(0): Using hardware cursor (scanline 960)
(II) fglrx(0): Largest offscreen area available: 1280 x 401
(**) Option "dpms"
(**) fglrx(0): DPMS enabled
(II) fglrx(0): Using XFree86 Acceleration Architecture (XAA)
Screen to screen bit blits
Solid filled rectangles
8x8 mono pattern filled rectangles
Solid Lines
Dashed Lines
Offscreen Pixmaps
Setting up tile and stipple cache:
30 128x128 slots
(II) fglrx(0): Acceleration enabled
(II) fglrx(0): X context handle = 0x00000001
(II) fglrx(0): [DRI] installation complete
(II) fglrx(0): Direct rendering enabled
(II) Loading extension FGLRXEXTENSION
(II) Loading extension ATITVOUT
(==) RandR enabled
(II) Setting vga for screen 0.
(II) Initializing built-in extension MIT-SHM
(II) Initializing built-in extension XInputExtension
(II) Initializing built-in extension XTEST
(II) Initializing built-in extension XKEYBOARD
(II) Initializing built-in extension LBX
(II) Initializing built-in extension XC-APPGROUP
(II) Initializing built-in extension SECURITY
(II) Initializing built-in extension XINERAMA
(II) Initializing built-in extension XFree86-Bigfont
(II) Initializing built-in extension RENDER
(II) Initializing built-in extension RANDR
(**) Option "Protocol" "ImPS/2"
(**) Mouse1: Protocol: "ImPS/2"
(**) Option "SendCoreEvents" "true"
(**) Mouse1: always reports core events
(**) Option "CorePointer"
(**) Mouse1: Core Pointer
(**) Option "Device" "/dev/input/mice"
(**) Option "Emulate3Buttons" "true"
(**) Mouse1: Emulate3Buttons, Emulate3Timeout: 50
(**) Option "ZAxisMapping" "4 5"
(**) Mouse1: ZAxisMapping: buttons 4 and 5
(**) Mouse1: Buttons: 5
(II) Keyboard "Keyboard1" handled by legacy driver
(II) XINPUT: Adding extended input device "Mouse1" (type: MOUSE)
(II) Mouse1: ps2EnableDataReporting: succeeded
Could not init font path element /usr/X11R6/lib/X11/fonts/Speedo/, removing from list!
GetModeLine - scrn: 0 clock: 148500
GetModeLine - hdsp: 1280 hbeg: 1344 hend: 1504 httl: 1728
vdsp: 960 vbeg: 961 vend: 964 vttl: 1011 flags: 5
И dmesg
Код: Выделить всё
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 439M
agpgart: Detected NVIDIA nForce2 chipset
agpgart: AGP aperture is 128M @ 0xd0000000
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE2: IDE controller at PCI slot 00:09.0
NFORCE2: chipset revision 162
NFORCE2: not 100% native mode: will probe irqs later
AMD_IDE: Bios didn't set cable bits corectly. Enabling workaround.
AMD_IDE: nVidia Corporation nForce2 IDE (rev a2) UDMA100 controller on pci00:09.0
ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA
hda: Maxtor 6Y080P0, ATA DISK drive
hdb: IBM-DTLA-307045, ATA DISK drive
blk: queue c041d3e0, I/O limit 4095Mb (mask 0xffffffff)
blk: queue c041d52c, I/O limit 4095Mb (mask 0xffffffff)
hdc: SAMSUNG CDRW/DVD SM-348B, ATAPI CD/DVD-ROM drive
hdd: IBM-DTLA-307045, ATA DISK drive
blk: queue c041d9a0, I/O limit 4095Mb (mask 0xffffffff)
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: attached ide-disk driver.
hda: host protected area => 1
hda: 160086528 sectors (81964 MB) w/7936KiB Cache, CHS=9964/255/63, UDMA(100)
hdb: attached ide-disk driver.
hdb: host protected area => 1
hdb: 90069840 sectors (46116 MB) w/1916KiB Cache, CHS=5606/255/63, UDMA(100)
hdd: attached ide-disk driver.
hdd: host protected area => 1
hdd: 90069840 sectors (46116 MB) w/1916KiB Cache, CHS=89355/16/63, UDMA(33)
hdc: attached ide-scsi driver.
Partition check:
hda: hda1 hda2
hdb: hdb1 hdb2 < hdb5 hdb6 >
hdd: [PTBL] [5606/255/63] hdd1 hdd2
SCSI subsystem driver Revision: 1.00
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: SAMSUNG Model: CDRW/DVD SM-348B Rev: T504
Type: CD-ROM ANSI SCSI revision: 02
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
sr0: scsi3-mmc drive: 8x/8x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.12
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
PCI: Setting latency timer of device 00:02.2 to 64
ehci_hcd 00:02.2: nVidia Corporation nForce2 USB Controller
ehci_hcd 00:02.2: irq 11, pci mem e0b9a000
usb.c: new USB bus registered, assigned bus number 1
PCI: cache line size of 64 is not supported by device 00:02.2
ehci_hcd 00:02.2: USB 2.0 enabled, EHCI 1.00, driver 2003-Dec-29/2.4
hub.c: USB hub found
hub.c: 6 ports detected
PCI: No IRQ known for interrupt pin A of device 00:02.0. Please try using pci=biosirq.
host/usb-ohci.c: found OHCI device with no IRQ assigned. check BIOS settings!
PCI: Setting latency timer of device 00:02.1 to 64
host/usb-ohci.c: USB OHCI at membase 0xe0b9c000, IRQ 12
host/usb-ohci.c: usb-00:02.1, nVidia Corporation nForce2 USB Controller (#2)
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 3 ports detected
usb.c: registered new driver usbscanner
scanner.c: 0.4.16:USB Scanner Driver
Linux video capture interface: v1.00
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 32768)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
FAT: bogus logical sector size 0
FAT: bogus logical sector size 0
kmod: failed to exec /sbin/modprobe -s -k nls_iso8859-1, errno = 2
UDF-fs DEBUG lowlevel.c:65:udf_get_last_session: CDROMMULTISESSION not supported: rc=-22
UDF-fs DEBUG super.c:1426:udf_read_super: Multi-session=0
UDF-fs DEBUG super.c:415:udf_vrs: Starting at sector 16 (2048 byte sectors)
UDF-fs: No VRS found
sh-2021: reiserfs_read_super: can not find reiserfs on ide0(3,1)
kmod: failed to exec /sbin/modprobe -s -k nls_iso8859-1, errno = 2
VFS: Mounted root (jfs filesystem) readonly.
Freeing unused kernel memory: 112k freed
hub.c: new USB device 00:02.1-3, assigned address 2
usb.c: USB device 2 (vend/prod 0x46d/0xc01b) is not claimed by any active driver.
usb.c: registered new driver usbmouse
input0: Logitech USB-PS/2 Optical Mouse on usb2:2.0
usbmouse.c: v1.6:USB HID Boot Protocol mouse driver
usb.c: registered new driver hiddev
usb.c: registered new driver hid
hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <vojtech@suse.cz>
hid-core.c: USB HID support drivers
mice: PS/2 mouse device common for all mice
Intel 810 + AC97 Audio, version 0.24, 16:18:26 Apr 7 2004
PCI: Setting latency timer of device 00:06.0 to 64
i810: NVIDIA nForce Audio found at IO 0xd800 and 0xd400, MEM 0x0000 and 0x0000, IRQ 12
i810_audio: Audio Controller supports 6 channels.
i810_audio: Defaulting to base 2 channel mode.
i810_audio: Resetting connection 0
ac97_codec: AC97 Audio codec, id: ALG32 (ALC650)
i810_audio: AC'97 codec 0, new EID value = 0x05c7
i810_audio: AC'97 codec 0, DAC map configured, total channels = 6
i810_audio: setting clocking to 48813
usb.c: registered new driver usbkbd
usbkbd.c: :USB HID Boot Protocol keyboard driver
i2c-core.o: i2c core module version 2.6.1 (20010830)
i2c-core.o: driver i2c TV tuner driver registered.
i2c-proc.o version 2.6.1 (20010830)
i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)
i2c-core.o: driver i2c-dev dummy driver registered.
i2c-algo-bit.o: i2c bit algorithm module
ip_conntrack version 2.1 (4095 buckets, 32760 max) - 292 bytes per conntrack
ip_tables: (C) 2000-2002 Netfilter core team
[fglrx] Maximum main memory to use for locked dma buffers: 430 MBytes.
[fglrx] module loaded - fglrx 3.7.6 [Mar 5 2004] on minor 0
XFS mounting filesystem ide0(3,2)
Ending clean XFS mount for filesystem: ide0(3,2)
reiserfs: found format "3.6" with standard journal
reiserfs: checking transaction log (device ide1(22,65)) ...
for (ide1(22,65))
ide1(22,65):Using r5 hash to sort names
ISO 9660 Extensions: Microsoft Joliet Level 3
ISO 9660 Extensions: RRIP_1991A
[fglrx] AGP detected, AgpState = 0x1f00421b (hardware caps of chipset)
[fglrx] AGP enabled, AgpCommand = 0x1f004312 (selected caps)
[fglrx] free AGP = 121909248
[fglrx] max AGP = 121909248
[fglrx] free LFB = 50266112
[fglrx] max LFB = 50266112
[fglrx] free Inv = 0
[fglrx] max Inv = 0
[fglrx] total Inv = 0
[fglrx] total TIM = 0
[fglrx] total FB = 0
[fglrx] total AGP = 32768
[fglrx] free AGP = 121909248
[fglrx] max AGP = 121909248
[fglrx] free LFB = 50266112
[fglrx] max LFB = 50266112
[fglrx] free Inv = 0
[fglrx] max Inv = 0
[fglrx] total Inv = 0
[fglrx] total TIM = 0
[fglrx] total FB = 0
[fglrx] total AGP = 32768
