Linux.by

Код: Выделить всё

Section "Module"

# This loads the DBE extension module.

    Load        "dbe"  	# Double buffer extension

# This loads the miscellaneous extensions module, and disables
# initialisation of the XFree86-DGA extension within that module.
    SubSection  "extmod"
      Option    "omit xfree86-dga"   # don't initialise the DGA extension
    EndSubSection

# This loads the Type1 and FreeType font modules
    Load        "type1"
    Load        "speedo"
#    Load        "freetype"
#    Load        "xtt"

# This loads the GLX module
#    Load       "glx"
# This loads the DRI module
#    Load       "dri"

EndSection

# **********************************************************************
# Files section.  This allows default font and rgb paths to be set
# **********************************************************************

Section "Files"

# The location of the RGB database.  Note, this is the name of the
# file minus the extension (like ".txt" or ".db").  There is normally
# no need to change the default.

    RgbPath	"/usr/X11R6/lib/X11/rgb"

#    FontPath   "/usr/X11R6/lib/X11/fonts/local/"
    FontPath   "/usr/X11R6/lib/X11/fonts/misc/"
    FontPath   "/usr/X11R6/lib/X11/fonts/75dpi/:unscaled"
#    FontPath   "/usr/X11R6/lib/X11/fonts/100dpi/:unscaled"
    FontPath   "/usr/X11R6/lib/X11/fonts/Speedo/"
    FontPath   "/usr/X11R6/lib/X11/fonts/Type1/"
#    FontPath   "/usr/X11R6/lib/X11/fonts/TrueType/"
#    FontPath   "/usr/X11R6/lib/X11/fonts/freefont/"
    FontPath   "/usr/X11R6/lib/X11/fonts/75dpi/"
#    FontPath   "/usr/X11R6/lib/X11/fonts/100dpi/"

# The module search path.  The default path is shown here.

#    ModulePath "/usr/X11R6/lib/modules"

EndSection

# **********************************************************************
# Server flags section.
# **********************************************************************

Section "ServerFlags"

# Uncomment this to cause a core dump at the spot where a signal is
# received.  This may leave the console in an unusable state, but may
# provide a better stack trace in the core dump to aid in debugging

#    Option "NoTrapSignals"

# Uncomment this to disable the <Crtl><Alt><Fn> VT switch sequence
# (where n is 1 through 12).  This allows clients to receive these key
# events.

#    Option "DontVTSwitch"

# Uncomment this to disable the <Crtl><Alt><BS> server abort sequence
# This allows clients to receive this key event.

#    Option "DontZap"

# Uncomment this to disable the <Crtl><Alt><KP_+>/<KP_-> mode switching
# sequences.  This allows clients to receive these key events.

#    Option "Dont Zoom"

# Uncomment this to disable tuning with the xvidtune client. With
# it the client can still run and fetch card and monitor attributes,
# but it will not be allowed to change them. If it tries it will
# receive a protocol error.

#    Option "DisableVidModeExtension"

# Uncomment this to enable the use of a non-local xvidtune client.

#    Option "AllowNonLocalXvidtune"

# Uncomment this to disable dynamically modifying the input device
# (mouse and keyboard) settings.

#    Option "DisableModInDev"

# Uncomment this to enable the use of a non-local client to
# change the keyboard or mouse settings (currently only xset).

#    Option "AllowNonLocalModInDev"

EndSection


# **********************************************************************
# Monitor section
# **********************************************************************

# Any number of monitor sections may be present

Section "Monitor"

    Identifier  "Samsung SyncMaster 753DF"

# HorizSync is in kHz unless units are specified.
# HorizSync may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY.  REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.

    HorizSync   30-70

#    HorizSync	30-64         # multisync
#    HorizSync	31.5, 35.2    # multiple fixed sync frequencies
#    HorizSync	15-25, 30-50  # multiple ranges of sync frequencies

# VertRefresh is in Hz unless units are specified.
# VertRefresh may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY.  REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.

    VertRefresh 50-160

vendorname "Samsung"
modelname "SyncMaster 753DF"
ModeLine "1024x768/85Hz" 98.9 1024 1056 1216 1408 768 782 788 822  -HSync -VSync
EndSection


# **********************************************************************
# Graphics device section
# **********************************************************************

# Any number of graphics device sections may be present

# Standard VGA Device:

Section "Device"
    Identifier	"Standard VGA"
    VendorName	"Intel"
    BoardName	"i815"

# The chipset line is optional in most cases.  It can be used to override
# the driver's chipset detection, and should not normally be specified.

#    Chipset	"generic"

# The Driver line must be present.  When using run-time loadable driver
# modules, this line instructs the server to load the specified driver
# module.  Even when not using loadable driver modules, this line
# indicates which driver should interpret the information in this section.

    Driver     "i810"
# The BusID line is used to specify which of possibly multiple devices
# this section is intended for.  When this line isn't present, a device
# section can only match up with the primary video device.  For PCI
# devices a line like the following could be used.  This line should not
# normally be included unless there is more than one video device
# intalled.

#    BusID      "PCI:0:10:0"

#    VideoRam	256

#    Clocks	25.2 28.3

EndSection

# Device configured by xf86config:

Section "Device"
    Identifier  "D815EFV"
    Driver      "i810"
    VideoRam    32768
    # Insert Clocks lines here if appropriate
vendorname "Intel"
boardname "i815"
EndSection


# **********************************************************************
# Screen sections
# **********************************************************************

# Any number of screen sections may be present.  Each describes
# the configuration of a single screen.  A single specific screen section
# may be specified from the X server command line with the "-screen"
# option.
Section "Screen"
    Identifier  "Screen 1"
    Device      "D815EFV"
    Monitor     "Samsung SyncMaster 753DF"
    DefaultDepth 24

    Subsection "Display"
        Depth       8
        Modes       "1024x768/85Hz" "1024x768" "800x600" "640x480" 
        ViewPort    0 0
		Virtual 0 0
    EndSubsection
    Subsection "Display"
        Depth       16
        Modes       "1024x768/85Hz" "1024x768" "800x600" "640x480" 
        ViewPort    0 0
		Virtual 0 0
    EndSubsection
    Subsection "Display"
        Depth       24
        Modes       "1024x768/85Hz" "1024x768" "800x600" "640x480"
        ViewPort    0 0
		Virtual 0 0
    EndSubsection
EndSection

# **********************************************************************
# ServerLayout sections.
# **********************************************************************

# Any number of ServerLayout sections may be present.  Each describes
# the way multiple screens are organised.  A specific ServerLayout
# section may be specified from the X server command line with the
# "-layout" option.  In the absence of this, the first section is used.
# When now ServerLayout section is present, the first Screen section
# is used alone.

Section "ServerLayout"

# The Identifier line must be present
    Identifier  "Simple Layout"

# Each Screen line specifies a Screen section name, and optionally
# the relative position of other screens.  The four names after
# primary screen name are the screens to the top, bottom, left and right
# of the primary screen.  In this example, screen 2 is located to the
# right of screen 1.

    Screen "Screen 1"

# Each InputDevice line specifies an InputDevice section name and
# optionally some options to specify the way the device is to be
# used.  Those options include "CorePointer", "CoreKeyboard" and
# "SendCoreEvents".

    InputDevice "Mouse1" "CorePointer"
    InputDevice "Keyboard1" "CoreKeyboard"

EndSection

# Section "DRI"
#    Mode 0666
# EndSection


Section "InputDevice"

Identifier "Keyboard1"
Driver "keyboard"

        Option "AutoRepeat" "500 30"
        Option "XkbRules" "xfree86"
	Option "XkbModel" "pc104"
	Option "XkbLayout" "ru"
	Option "XkbOptions" "grp:ctrl_shift_toggle"

EndSection


Section "InputDevice"

Identifier "Mouse1"
Driver "mouse"

	Option "Protocol" "auto"
	Option "Device" "/dev/psaux"
	Option "ZAxisMapping" "4 5"
EndSection 

Код: Выделить всё

ModeLine "1024x768/85Hz" 98.9 1024 1056 1216 1408 768 782 788 822  -HSync -VSync 
~skip~
    DefaultDepth 24 
~skip~
       Depth       24
        Modes       "1024x768/85Hz" "1024x768" "800x600" "640x480"